Kindle 10 LED Status Light Replacement

Giriş

The LED light on the Kindle 10 is a sturdy and efficient piece of technology connected to the motherboard that indicates different statuses: a blinking orange for charging and continuously lit when charged. It is not expected to need replacement for its filament should last over 100 years. There may be issues with the light if the Kindle is functional but the light does not react to actions such as charging or powering off. If its soldering points become disconnected or the filament does burn out, we can replace this light.

Neye ihtiyacın var

Adım 1 Battery

Kindle 10 LED Status Light Replacement, Battery: adım 1, 2 resimden 1.

Kindle 10 LED Status Light Replacement, Battery: adım 1, 2 resimden 2.

Gently use a metal spudger to pry, twist, and lift the bezel away from the display.

Düzenle

Adım 2

Remove the eight 2.6 mm screws using a T5 Torx screwdriver.

Düzenle

Adım 3

Use the metal spudger to gently lift the screen out of the back frame.

Düzenle

Adım 4

Detach the battery connector from the motherboard.
The battery pack may be glued on to the gray plastic frame. Take care when prying it out not to rip the battery, since it is made of a lithium polymer which is flammable and deforms easily.

Düzenle

Adım 5 Motherboard

Kindle 10 LED Status Light Replacement, Motherboard: adım 5, 3 resimden 1.

Kindle 10 LED Status Light Replacement, Motherboard: adım 5, 3 resimden 2.

Kindle 10 LED Status Light Replacement, Motherboard: adım 5, 3 resimden 3.

Remove the two outer silver screws with a T5 Torx screwdriver.
Use your fingers to remove the two gold screws in the middle.

Düzenle

Adım 6

Kindle 10 LED Status Light Replacement: adım 6, 3 resimden 3.

Disconnect the two orange clear plastic ribbons on the upper right and center.

Düzenle

Adım 7

Pry the motherboard away from the display frame

Düzenle

Adım 8 LED Status Light

Kindle 10 LED Status Light Replacement, LED Status Light: adım 8, 3 resimden 1.

Kindle 10 LED Status Light Replacement, LED Status Light: adım 8, 3 resimden 2.

Kindle 10 LED Status Light Replacement, LED Status Light: adım 8, 3 resimden 3.

Follow the guide How To Solder to prepare your soldering iron.
Turn on the soldering iron.
Clean the tip after the old solder has melted by dragging it across a sponge.
Prime the soldering iron by touching its tip with a dab of lead-free wire. Your soldering iron is ready when the solder readily melts.

Düzenle

Adım 9

Kindle 10 LED Status Light Replacement: adım 9, 3 resimden 3.

Touch the soldering iron's tip to the two joints on the front and back of the LED for 5 seconds, or longer if it is not melted.
Use tweezers to pull out the LED once it is loosened.
Always use tweezers to handle components near the soldering tip as it will be hot.

Düzenle

Adım 10

Kindle 10 LED Status Light Replacement: adım 10, 3 resimden 3.

Search for "Through-Hole Soldering" on this How To Solder guide to ensure you replace and solder the LED correctly.
Align your new replacement LED in the correct location.
Pull the wires on each side of the new LED through the holes in the circuit where the LED was previously.
Solder its joints in the back. Be sure the soldering joints create a concave tent shape indicating a strong connection.
Use a tool such as tweezers to hold the new LED in place so that your hands are not near the hot soldering iron.